{"id":3702,"date":"2026-11-03T22:24:11","date_gmt":"2026-11-03T14:24:11","guid":{"rendered":"http:\/\/www.anilaoiloilo.com\/blog\/?p=3702"},"modified":"2026-11-03T22:24:11","modified_gmt":"2026-11-03T14:24:11","slug":"how-to-troubleshoot-a-positive-displacement-pump-that-won-t-prime-46e0-bc9c99","status":"publish","type":"post","link":"http:\/\/www.anilaoiloilo.com\/blog\/2026\/11\/03\/how-to-troubleshoot-a-positive-displacement-pump-that-won-t-prime-46e0-bc9c99\/","title":{"rendered":"How to troubleshoot a positive displacement pump that won&#8217;t prime?"},"content":{"rendered":"<p>Hey there, if you\u2019re here, odds are you\u2019re staring down a positive displacement pump that just won\u2019t prime, and it\u2019s killing your whole operation\u2014been there, and as the owner-operator of a positive displacement system supply company, I\u2019ve walked more folks through this mess than I can count. Let\u2019s cut the corporate fluff and get real: priming issues with PD pumps aren\u2019t just a minor hiccup\u2014they shut down production, waste time, and if you hack it wrong, you can actually damage the pump. <a href=\"https:\/\/www.ishanlube.com\/lubrication-system\/positive-displacement-system\/\">Positive Displacement System<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.ishanlube.com\/uploads\/44900\/small\/grease-nipple-joint38f9e.jpg\"><\/p>\n<p>First, let\u2019s keep this grounded in how PD pumps actually work, because half the time, folks skip this and guess, which makes the fix way harder. Unlike centrifugal pumps that rely on velocity to move fluid, PD pumps trap a fixed volume of liquid in their chambers (think gears, lobes, pistons, or diaphragms) and physically shove it out. For priming, that means two non-negotiables: first, the pump chamber has to be completely full of liquid\u2014no air bubbles, no empty spots\u2014and second, you have to prime it properly so that fixed volume movement can pull in more liquid from the suction side. If either of those is off, the pump\u2019s just churning air, not moving fluid, and that\u2019s when the \u201cwon\u2019t prime\u201d panic hits.<\/p>\n<p>Let\u2019s walk through the troubleshooting step-by-step, like we\u2019re leaning over your pump right now, no jargon overload, just stuff you can check today.<\/p>\n<p>First stop: the suction line, hands down. 90% of priming problems with PD pumps start here, not the pump itself. Let\u2019s break this down. First, is the suction valve open? Duh, sounds basic, but I\u2019ve seen guys walk away for a smoke and come back to a valve still cranked shut\u2014don\u2019t be that person. Next, check for leaks on the suction side. PD pumps create a strong vacuum on the suction side to pull fluid in, so even a tiny leak (think a cracked flange gasket, a loose pipe fitting, or a hole in the suction hose) will let air seep in, and that\u2019s the enemy of priming. How to spot this? If you cap the suction line temporarily and the pump primes easily, you\u2019ve got a suction leak. Don\u2019t just \u201ctighten fittings\u201d\u2014get a mirror and a light to check every joint, especially if you\u2019re using flexible hose (they get worn from abrasion). Also, make sure the suction line size isn\u2019t too small. If you cram a 2-inch hose onto a 1-inch pump suction, the fluid can\u2019t flow fast enough to fill the pump chamber before the next cycle, so you end up with air in there. Rule of thumb: suction line should be equal or larger diameter than the pump\u2019s suction port. If it\u2019s smaller, that\u2019s a quick fix to test.<\/p>\n<p>Next up: is the pump primed <em>before<\/em> you start it? A lot of people with centrifugal pump experience make the mistake here\u2014centrifugal pumps often self-prime if you fill the casing once, but PD pumps? Most can\u2019t do that, especially if they\u2019re dry. For gear pumps, lobe pumps, and piston pumps, you have to manually prime the casing first. How? Pour fluid into the pump\u2019s priming port (that little plug on top or side of the pump casing) until it overflows out, air bubbles gone, then plug it back up. I\u2019ve seen folks skip this because they\u2019re in a hurry, and that\u2019s the #1 avoidable mistake. Diaphragm pumps are a little different\u2014many have a priming mechanism (usually a purge valve on the suction side) you have to open to bleed air until liquid comes out, then close it before starting. Also, watch for this: if you prime it, then the second you open the suction valve, it loses prime? That goes back to the suction leak we talked about, but sometimes it\u2019s also a bad check valve on the suction side\u2014those little one-way valves keep fluid from flowing back out when you stop, but if they\u2019re stuck closed, dirty, or worn, they won\u2019t hold the prime. Pop that check valve out, clean it, or replace it if it\u2019s scored.<\/p>\n<p>Now, what about the inlet conditions? Is the fluid you\u2019re moving too viscous? PD pumps handle thick stuff great, but if the fluid\u2019s way more viscous than the pump was sized for, it won\u2019t flow fast enough into the pump chambers to fill them. For example, if you sized a pump for thin water, then start pumping heavy grease or molasses in cold weather, the suction line drags on the fluid so much that the pump can\u2019t pull it in, so you end up with air and no prime. Test this by warming the fluid a little (if that\u2019s safe for your process) or checking the pump\u2019s viscosity rating\u2014we always give these specs with every system we supply, but if you lost your docs, most PD pump manuals list max viscosity at operating temp. Another common inlet issue: vapor pressure. If the fluid is hot enough, it turns to vapor, which acts just like air and breaks the vacuum. That\u2019s why pumping hot liquids often needs a flooded suction line (so the suction line is full of fluid at a higher pressure than the pump\u2019s inlet) instead of a vacuum lift. If you\u2019re running a hot fluid, and the suction line is drawn up from a tank below the pump, that\u2019s the problem\u2014switch to a flooded suction tank, or raise the tank level so the fluid is above the pump suction port, and the pressure will push fluid into the pump, not rely on vacuum.<\/p>\n<p>Okay, so the suction side checks out, you primed it manually, fluid\u2019s the right viscosity, no vapor\u2014now it\u2019s pump parts time. First, check the pump\u2019s internal clearances. PD pumps need tight clearances between the rotating parts (gears, lobes, pistons) and the casing to create that strong suction vacuum. If those clearances are worn out\u2014say, the pump is old, you ran it dry once and scored the lobes\u2014air leaks past those clearances right into the discharge side, so the vacuum on the suction side drops too low to pull fluid in. How to test this? If you run the pump with the discharge valve closed <em>briefly<\/em> (like 10-15 seconds max\u2014don\u2019t let it run dead head longer, that can damage the seals), the pump should build pressure, which means the clearances are still good. If it can\u2019t build pressure, you\u2019ve got worn internal parts. Also, check the seals\u2014mechanical seals or packing on PD pumps are there to keep air from getting in from the drive side, not just fluid from leaking out. If the seal is worn, air is seeping into the pump shaft area, breaking the vacuum. Leaks here usually show as fluid dripping, but sometimes internal leaks are hidden\u2014if you see air coming out of the seal area when running at prime, that\u2019s a dead giveaway.<\/p>\n<p>Wait, what about the rotation direction? Yeah, this is super basic but so easy to mess up. PD pumps only work if you rotate them the right way\u2014reverse the rotation, and the chambers open outward instead of trapping fluid, so you\u2019re pumping air, not liquid. How to check? Most pumps have a rotation arrow on the casing. If you wired the motor wrong and it\u2019s spinning the opposite way, that\u2019s your issue. Turn off power, double check the motor leads, swap two wires, test it\u2014done. I can\u2019t tell you how many field calls we got last year from installers who flipped two wires and wasted 4 hours.<\/p>\n<p>Now, let\u2019s talk about some less common, still real, issues. If you\u2019re using a double-diaphragm pump, check the diaphragm valves\u2014the little check valves that open and close with each pump cycle. If they\u2019re worn, clogged with debris, or installed backwards, they won\u2019t let fluid flow in or out right, so the pump can\u2019t prime. I once had a customer who ran a slurry through a diaphragm pump and got a chunk of trash stuck in the inlet valve, so it wouldn\u2019t open to pull fluid in\u2014cleaned the valve, fixed it in 10 minutes. Also, suction lift height: PD pumps can only pull fluid so far via vacuum, usually max 15-20 feet, depending on the fluid\u2019s viscosity and temperature. If your suction lift is higher than that, the vacuum needed would be more than atmospheric pressure can provide, so you\u2019ll never get prime. That\u2019s where flooded suction comes in, like we talked about earlier.<\/p>\n<p>Wait, let\u2019s circle back to what we learned as a PD system supplier\u2014most folks try to fix this themselves, and they make it worse. For example, if they hear it\u2019s a suction leak, they cram sealant around every fitting, which can get into the pump and clog parts. Or they prime it over and over while running the pump dry, which can burn up seals or scoring internal parts. That\u2019s why we always tell folks to start with the simple checks first: valve open, suction leaks, manual priming, rotation direction, then move to more complex stuff.<\/p>\n<p>Now, if you\u2019ve gone through every single step here and it\u2019s still not priming? Don\u2019t keep guessing\u2014call a pro who knows PD pumps, not centrifugal. As a PD system supplier, we\u2019re on call for exactly this, whether you need a quick troubleshooting walkthrough or want to make sure your pump is sized right for your application. Priming issues rarely mean you need a whole new pump\u2014most of the time, it\u2019s a $5 gasket, a 10-minute clean, or swapping two motor wires.<\/p>\n<p>A quick recap so you don\u2019t forget: 1. Suction line: open valve, no leaks, right size, no small pipes. 2. Manual priming: don\u2019t rely on self-prime, fill until overflow, bleed air. 3. Inlet conditions: fluid viscosity, no vapor pressure, enough suction lift or flooded suction. 4. Pump internals: check rotation, seals, clearances, check valves. 5. No guessing beyond that\u2014don\u2019t damage your pump by running it dry.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.ishanlube.com\/uploads\/202544900\/small\/variable-positive-displacement-pumps1aae5250-5118-405f-a1e0-c3e40e80edee.jpg\"><\/p>\n<p>At the end of the day, PD pump priming problems are solvable 9 times out of 10 with a methodical check, no fancy tools needed. If you\u2019re still stuck after going through this, reach out to our team for help\u2014we\u2019ll walk you through it step by step, no sales pitch, just real advice from folks who work with PD pumps every single day. Don\u2019t let a priming issue shut down your whole line\u2014fix it right the first time.<\/p>\n<p><a href=\"https:\/\/www.ishanlube.com\/lubrication-system\/resistive-systems\/\">Resistive Systems<\/a> References<\/p>\n<ol>\n<li>Karassik, I. J., Messina, J. P., Cooper, P., &amp; Heald, C. C. (2007). Pump Handbook (4th ed.). McGraw-Hill.<\/li>\n<li>Hydraulic Institute. (2018). Positive Displacement Pump Installation, Operation, and Maintenance Guidelines. Hydraulic Institute.<\/li>\n<li>American Petroleum Institute. (2020). API Standard 675: Positive Displacement Pumps \u2013 Controlled Volume. American Petroleum Institute.<\/li>\n<li>The Pump Center. (2022). Common Priming Issues with Positive Displacement Pumps: A Troubleshooting Guide. Industrial Pump and Equipment Blog.<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.ishanlube.com\/\">Sunshine Machinery Co., Ltd.<\/a><br \/>As one of the most professional positive displacement system manufacturers and suppliers in China, our products have good reputation in the market. Please rest assured to buy durable positive displacement system made in China here from our factory. For price consultation, contact us.<br \/>Address: No.852, Qingfeng South Road (South), Tongxiang City, Zhejiang Province<br \/>E-mail: export@ishan.com.cn<br \/>WebSite: <a href=\"https:\/\/www.ishanlube.com\/\">https:\/\/www.ishanlube.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Hey there, if you\u2019re here, odds are you\u2019re staring down a positive displacement pump that just &hellip; <a title=\"How to troubleshoot a positive displacement pump that won&#8217;t prime?\" class=\"hm-read-more\" href=\"http:\/\/www.anilaoiloilo.com\/blog\/2026\/11\/03\/how-to-troubleshoot-a-positive-displacement-pump-that-won-t-prime-46e0-bc9c99\/\"><span class=\"screen-reader-text\">How to troubleshoot a positive displacement pump that won&#8217;t prime?<\/span>Read more<\/a><\/p>\n","protected":false},"author":437,"featured_media":3702,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3665],"class_list":["post-3702","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-positive-displacement-system-425a-bcd5e2"],"_links":{"self":[{"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/posts\/3702","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/users\/437"}],"replies":[{"embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/comments?post=3702"}],"version-history":[{"count":0,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/posts\/3702\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/posts\/3702"}],"wp:attachment":[{"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/media?parent=3702"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/categories?post=3702"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/tags?post=3702"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}