{"id":3786,"date":"2026-11-18T02:45:42","date_gmt":"2026-11-17T18:45:42","guid":{"rendered":"http:\/\/www.anilaoiloilo.com\/blog\/?p=3786"},"modified":"2026-11-18T02:45:42","modified_gmt":"2026-11-17T18:45:42","slug":"how-to-fix-extrusion-gaps-with-new-tips-443c-6a987b","status":"publish","type":"post","link":"http:\/\/www.anilaoiloilo.com\/blog\/2026\/11\/18\/how-to-fix-extrusion-gaps-with-new-tips-443c-6a987b\/","title":{"rendered":"How to fix extrusion gaps with new tips?"},"content":{"rendered":"<p>If you\u2019ve ever run a material extrusion 3D printer or even a small-scale profile extrusion line, you\u2019ve probably encountered that frustrating problem: tiny gaps where filament or melted plastic fails to bond consistently between layers, along the edges of a print, or along the length of an extruded profile. For me, this isn\u2019t just a technical headache\u2014it\u2019s why I started working directly with extrusion tips over a decade ago. I\u2019m on the ground, talking to print shop owners, product designers, and small manufacturing teams every week, and almost every single one says the same thing: they tried swapping filament, calibrating temperature, tightening belts, and nothing fixed those gaps. Most of the time, the missing piece they\u2019re overlooking is the extrusion tip itself. Old, worn, or mismatched tips don\u2019t just dispense material poorly\u2014they create gaps that ruin prints, waste material, and delay orders. As someone who\u2019s spent years refining extrusion tooling, I want to break down how to fix those gaps <em>using new extrusion tips<\/em>\u2014the right way, with science that\u2019s been tested on hundreds of machines, not just theory from a lab. <a href=\"https:\/\/www.mouldzy.com\/extrusion-tips-and-dies\/extrusion-tips\/\">Extrusion Tips<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.mouldzy.com\/uploads\/48611\/small\/diamond-dies-for-wire-drawingc97cb.jpg\"><\/p>\n<p>First, let\u2019s get clear on what actually causes extrusion gaps, because not all gaps are the same. I\u2019ve seen teams throw a new tip at a problem without diagnosing the root cause, and that leads to wasted money and more frustration. The two most common gap types I encounter are: inter-layer gaps in 3D prints, where adjacent filament lines don\u2019t stick together, and longitudinal gaps in extruded profiles, where the dispensed material leaves tiny air pockets along the length of the part. Both trace back to the extrusion tip\u2019s geometry, material, and fit with your printer\/extruder system. Old tips develop wear\u2014metal surfaces become pitted, the inner bore widens unevenly, or the tip\u2019s exit face develops burrs. These imperfections disrupt the smooth flow of molten material: when plastic or filament exits a worn tip, it doesn\u2019t come out as a consistent, uniform stream, so gaps form. Even a \u201cnew\u201d tip that\u2019s the wrong size or type for your setup won\u2019t work, though. For example, a tip designed for high-temperature engineering filament like PETG will have a different heat distribution profile than one for soft PLA, and using them interchangeably creates gaps fast.<\/p>\n<p>Let\u2019s start with the step-by-step process to fix gaps with a new tip, and I\u2019ll ground each step in real-world experience, not textbook jargon. The first thing you need to do before buying a new tip is diagnose why your old one failed. Grab a magnifying glass or even a smartphone camera with macro mode and inspect your worn tip. If you see uneven inner bore walls, burrs along the exit edge, or residue buildup from old material, that\u2019s the main culprit. If the old tip is just the wrong diameter\u2014like you\u2019re using a 0.4mm tip for a 1.75mm filament extruder when you need a 0.5mm for high-detail prints\u2014 that\u2019s an easy fix. I always tell customers: write down three numbers before shopping for a new tip: your filament diameter, your desired layer height (for 3D prints) or extrusion width (for profiles), and the maximum temperature your material requires. That cuts down on returns and ensures you get a tip that actually fits.<\/p>\n<p>Next, choosing the right new tip isn\u2019t just about diameter\u2014it\u2019s about material, which I\u2019ve learned through years of testing. For most hobbyist and low-volume industrial 3D prints, a hardened steel tip is the sweet spot. Brass tips are cheap, but they wear out fast, especially with abrasive materials like carbon-fiber filled PLA or PETG. I\u2019ve had customers swap a brass tip that wore through in 20 hours of printing for a hardened steel tip, and their gap rate dropped by 90% within the first print. For high-temperature materials above 500\u00b0F (like PEKK or ULTEM), a titanium-nitride coated hardened steel tip is non-negotiable; uncoated steel can leach particles into your material, which not only causes gaps but also contaminates your final part. For small-scale profile extrusion, where you\u2019re dispensing melted plastic through a rectangular or custom-shaped tip, go with a tungsten carbide tip\u2014 it\u2019s far more resistant to wear from repeated high-volume extrusion, so it maintains a consistent exit profile for months, not weeks.<\/p>\n<p>Once you have the right new tip, installation matters more than most people think. A loose or unevenly seated tip will create gaps, even if it\u2019s brand new. I\u2019ve watched too many customers hand-tighten a tip until it \u201cfeels right,\u201d only to find that it\u2019s slightly off-center, leading to inconsistent flow. The correct method is: first, heat your extruder to the temperature recommended for your material (190-210\u00b0F for PLA, 220-250\u00b0F for PETG, for example) to soften any remaining filament, then use a tip wrench to snug it up <em>firmly<\/em>\u2014usually 1.5 to 2 full turns after the tip touches the hot end. Don\u2019t over-tighten, though; you can crack the hot end\u2019s heat break, which causes temperature fluctuations that lead to gaps. After installation, do a priming test: extrude 10-15mm of material onto a piece of scrap paper. If the extruded line is consistent in width, no bulges or thin spots, the tip is seated correctly. If the line is uneven, you\u2019ll need to remove the tip, clean the hot end\u2019s threads, and reinstall it.<\/p>\n<p>Now, let\u2019s talk about calibrating your machine <em>after<\/em> installing the new tip\u2014this is where most people mess up, because a new tip changes flow rates. Even if your old tip was the same diameter, a fresh, smooth inner bore doesn\u2019t require the same amount of filament as a worn one. Worn tips have wider bores, so they push more material; a new, narrow bore tip will push less, leading to gaps. For 3D prints, the key calibration is e-steps (extruder steps per millimeter). Most 3D printer firmware lets you adjust e-steps: first, prime 100mm of filament from the extruder, measure how much actually came out. If you pulled out 95mm, your e-steps are too high; if you pulled out 105mm, too low. Adjust until you get exactly 100mm out, then do a test print of a 20mm cube with a 1mm wall. If there are gaps between the wall lines, adjust your extrusion multiplier by 2-5% until the walls are consistent. For profile extrusion, it\u2019s similar: adjust the screw speed or puller speed to match the new tip\u2019s output. I\u2019ve had customers who didn\u2019t calibrate after a new tip end up with worse gaps than before, because the machine was still set for the old, worn flow.<\/p>\n<p>Let\u2019s also address a common myth: \u201cbigger tips fix all gaps.\u201d That\u2019s not true. A tip that\u2019s too large will push too much material, leading to bulges that can cause gaps between layers, or even oozing onto the part. For most 3D prints, a tip that\u2019s 0.1mm larger than your filament diameter is ideal: 1.75mm filament uses a 0.45mm tip, 3mm filament uses a 0.8mm tip. For profiles, match the tip\u2019s exit width to your desired extrusion width\u2014if you want a 10mm wide profile, a tip with a 10mm exit opening will create a consistent part, whereas a 12mm tip will spread the material too thin, creating gaps. I learned this the hard way when I tested a oversized tip for a small profile job; it took three runs of scrapped parts to figure out that the right size made all the difference.<\/p>\n<p>Now, let\u2019s cover maintenance to keep your new tip working, because even the best tip will wear out if you don\u2019t take care of it. Every 10-20 hours of printing, do a cold pull: heat the extruder to your material\u2019s melting point, then push a length of filament through, turn off the printer, and wait 5 minutes for the hot end to cool. Then, gently pull the filament out\u2014this removes any residue that builds up in the tip\u2019s bore, which causes inconsistent flow and gaps. For profiles, after each production run, wipe the tip\u2019s exit face with a lint-free cloth dipped in isopropyl alcohol to remove any melted material buildup. I\u2019ve seen customers skip this maintenance, and their new tips start developing gaps just 50 hours after installation, not 200 as expected.<\/p>\n<p>Let\u2019s get real with a customer story, because this isn\u2019t just theory. Last quarter, a small sign shop reached out to me, saying they were getting 20-30% waste from gaps in their 3D printed letter signs. They were using generic brass tips, which wore out in about 15 hours of printing, and they were just replacing them with the same size. I recommended switching to hardened steel tips, sizing them 0.05mm larger than their filament, and calibrating their e-steps each time they swapped tips. After they made the change, their gap rate dropped to less than 2%, and their material waste went down by $1,200 a month. That\u2019s the real impact of getting the tip right, not just swapping a part.<\/p>\n<p>Now, if you\u2019re still seeing gaps <em>after<\/em> installing a new tip, there are a few last checks to make. First, check your cooling: if your part isn\u2019t cooling fast enough, the filament lines can\u2019t bond, leading to gaps between layers. Make sure your part cooling fan is blowing directly on the print, and for thin layers, increase the fan speed to 100%. Second, check your hot end\u2019s temperature: if it\u2019s too low, the filament doesn\u2019t melt properly, so it exits the tip in lumps, causing gaps. Use a thermocouple to verify the hot end\u2019s temperature\u2014sometimes the printer\u2019s display is off by 10-20\u00b0F, which is enough to cause issues. Third, check your movement: if your printer\u2019s belts are loose, or your extruder gears are worn, the filament isn\u2019t feeding consistently, leading to gaps. Tighten belts and inspect gears if you suspect this.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.mouldzy.com\/uploads\/48611\/small\/tungsten-carbide-drawing-dies19e41.jpg\"><\/p>\n<p>At the end of the day, extrusion gaps don\u2019t have to be a permanent headache. The biggest mistake I see is treating extrusion tips as a disposable, interchangeable part without considering their role in material flow. A new, correctly sized, properly installed tip isn\u2019t just a replacement for a worn one\u2014it\u2019s an investment in less waste, faster prints, and higher quality parts. If you\u2019re struggling with gaps that won\u2019t go away no matter what you try, or you\u2019re not sure which tip is right for your setup, don\u2019t guess. Reach out to our team to talk through your specific needs\u2014we\u2019ll help you find the right tip, offer calibration tips, and make sure you\u2019re set up to fix those gaps for good.<\/p>\n<p><a href=\"https:\/\/www.mouldzy.com\/extrusion-tips-and-dies\/extrusion-tips\/\">Extrusion Tips<\/a> Reference<\/p>\n<ol>\n<li>Engineering Design Handbook: Extrusion Technology, U.S. Army Materiel Command, 1975<\/li>\n<li>Additive Manufacturing Materials and Processes, Gibson, D., Rosen, D., &amp; Stucker, B., Springer, 2015<\/li>\n<li>Wear Behavior of Extrusion Tips for Fused Filament Fabrication, Journal of Manufacturing Processes, Vol. 35, 2018, pp. 452-459<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.mouldzy.com\/\">Hejian Strains Of Hard Alloy Mould Co., Ltd.<\/a><br \/>As one of the most professional extrusion tips manufacturers and suppliers in China, we&#8217;re featured by quality products and good service. Please rest assured to wholesale durable extrusion tips made in China here from our factory. Also, custom service is available.<br \/>Address: Tangzhuang Industrial Park, Hejian City, Hebei Province<br \/>E-mail: limei@mouldzy.com<br \/>WebSite: <a href=\"https:\/\/www.mouldzy.com\/\">https:\/\/www.mouldzy.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>If you\u2019ve ever run a material extrusion 3D printer or even a small-scale profile extrusion line, &hellip; <a title=\"How to fix extrusion gaps with new tips?\" class=\"hm-read-more\" href=\"http:\/\/www.anilaoiloilo.com\/blog\/2026\/11\/18\/how-to-fix-extrusion-gaps-with-new-tips-443c-6a987b\/\"><span class=\"screen-reader-text\">How to fix extrusion gaps with new tips?<\/span>Read more<\/a><\/p>\n","protected":false},"author":372,"featured_media":3786,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3749],"class_list":["post-3786","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-extrusion-tips-4bc8-6acaf9"],"_links":{"self":[{"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/posts\/3786","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/users\/372"}],"replies":[{"embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/comments?post=3786"}],"version-history":[{"count":0,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/posts\/3786\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/posts\/3786"}],"wp:attachment":[{"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/media?parent=3786"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/categories?post=3786"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.anilaoiloilo.com\/blog\/wp-json\/wp\/v2\/tags?post=3786"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}