Posted in

How to fix extrusion gaps with new tips?

If you’ve ever run a material extrusion 3D printer or even a small-scale profile extrusion line, you’ve probably encountered that frustrating problem: tiny gaps where filament or melted plastic fails to bond consistently between layers, along the edges of a print, or along the length of an extruded profile. For me, this isn’t just a technical headache—it’s why I started working directly with extrusion tips over a decade ago. I’m on the ground, talking to print shop owners, product designers, and small manufacturing teams every week, and almost every single one says the same thing: they tried swapping filament, calibrating temperature, tightening belts, and nothing fixed those gaps. Most of the time, the missing piece they’re overlooking is the extrusion tip itself. Old, worn, or mismatched tips don’t just dispense material poorly—they create gaps that ruin prints, waste material, and delay orders. As someone who’s spent years refining extrusion tooling, I want to break down how to fix those gaps using new extrusion tips—the right way, with science that’s been tested on hundreds of machines, not just theory from a lab. Extrusion Tips

First, let’s get clear on what actually causes extrusion gaps, because not all gaps are the same. I’ve seen teams throw a new tip at a problem without diagnosing the root cause, and that leads to wasted money and more frustration. The two most common gap types I encounter are: inter-layer gaps in 3D prints, where adjacent filament lines don’t stick together, and longitudinal gaps in extruded profiles, where the dispensed material leaves tiny air pockets along the length of the part. Both trace back to the extrusion tip’s geometry, material, and fit with your printer/extruder system. Old tips develop wear—metal surfaces become pitted, the inner bore widens unevenly, or the tip’s exit face develops burrs. These imperfections disrupt the smooth flow of molten material: when plastic or filament exits a worn tip, it doesn’t come out as a consistent, uniform stream, so gaps form. Even a “new” tip that’s the wrong size or type for your setup won’t work, though. For example, a tip designed for high-temperature engineering filament like PETG will have a different heat distribution profile than one for soft PLA, and using them interchangeably creates gaps fast.

Let’s start with the step-by-step process to fix gaps with a new tip, and I’ll ground each step in real-world experience, not textbook jargon. The first thing you need to do before buying a new tip is diagnose why your old one failed. Grab a magnifying glass or even a smartphone camera with macro mode and inspect your worn tip. If you see uneven inner bore walls, burrs along the exit edge, or residue buildup from old material, that’s the main culprit. If the old tip is just the wrong diameter—like you’re using a 0.4mm tip for a 1.75mm filament extruder when you need a 0.5mm for high-detail prints— that’s an easy fix. I always tell customers: write down three numbers before shopping for a new tip: your filament diameter, your desired layer height (for 3D prints) or extrusion width (for profiles), and the maximum temperature your material requires. That cuts down on returns and ensures you get a tip that actually fits.

Next, choosing the right new tip isn’t just about diameter—it’s about material, which I’ve learned through years of testing. For most hobbyist and low-volume industrial 3D prints, a hardened steel tip is the sweet spot. Brass tips are cheap, but they wear out fast, especially with abrasive materials like carbon-fiber filled PLA or PETG. I’ve had customers swap a brass tip that wore through in 20 hours of printing for a hardened steel tip, and their gap rate dropped by 90% within the first print. For high-temperature materials above 500°F (like PEKK or ULTEM), a titanium-nitride coated hardened steel tip is non-negotiable; uncoated steel can leach particles into your material, which not only causes gaps but also contaminates your final part. For small-scale profile extrusion, where you’re dispensing melted plastic through a rectangular or custom-shaped tip, go with a tungsten carbide tip— it’s far more resistant to wear from repeated high-volume extrusion, so it maintains a consistent exit profile for months, not weeks.

Once you have the right new tip, installation matters more than most people think. A loose or unevenly seated tip will create gaps, even if it’s brand new. I’ve watched too many customers hand-tighten a tip until it “feels right,” only to find that it’s slightly off-center, leading to inconsistent flow. The correct method is: first, heat your extruder to the temperature recommended for your material (190-210°F for PLA, 220-250°F for PETG, for example) to soften any remaining filament, then use a tip wrench to snug it up firmly—usually 1.5 to 2 full turns after the tip touches the hot end. Don’t over-tighten, though; you can crack the hot end’s heat break, which causes temperature fluctuations that lead to gaps. After installation, do a priming test: extrude 10-15mm of material onto a piece of scrap paper. If the extruded line is consistent in width, no bulges or thin spots, the tip is seated correctly. If the line is uneven, you’ll need to remove the tip, clean the hot end’s threads, and reinstall it.

Now, let’s talk about calibrating your machine after installing the new tip—this is where most people mess up, because a new tip changes flow rates. Even if your old tip was the same diameter, a fresh, smooth inner bore doesn’t require the same amount of filament as a worn one. Worn tips have wider bores, so they push more material; a new, narrow bore tip will push less, leading to gaps. For 3D prints, the key calibration is e-steps (extruder steps per millimeter). Most 3D printer firmware lets you adjust e-steps: first, prime 100mm of filament from the extruder, measure how much actually came out. If you pulled out 95mm, your e-steps are too high; if you pulled out 105mm, too low. Adjust until you get exactly 100mm out, then do a test print of a 20mm cube with a 1mm wall. If there are gaps between the wall lines, adjust your extrusion multiplier by 2-5% until the walls are consistent. For profile extrusion, it’s similar: adjust the screw speed or puller speed to match the new tip’s output. I’ve had customers who didn’t calibrate after a new tip end up with worse gaps than before, because the machine was still set for the old, worn flow.

Let’s also address a common myth: “bigger tips fix all gaps.” That’s not true. A tip that’s too large will push too much material, leading to bulges that can cause gaps between layers, or even oozing onto the part. For most 3D prints, a tip that’s 0.1mm larger than your filament diameter is ideal: 1.75mm filament uses a 0.45mm tip, 3mm filament uses a 0.8mm tip. For profiles, match the tip’s exit width to your desired extrusion width—if you want a 10mm wide profile, a tip with a 10mm exit opening will create a consistent part, whereas a 12mm tip will spread the material too thin, creating gaps. I learned this the hard way when I tested a oversized tip for a small profile job; it took three runs of scrapped parts to figure out that the right size made all the difference.

Now, let’s cover maintenance to keep your new tip working, because even the best tip will wear out if you don’t take care of it. Every 10-20 hours of printing, do a cold pull: heat the extruder to your material’s melting point, then push a length of filament through, turn off the printer, and wait 5 minutes for the hot end to cool. Then, gently pull the filament out—this removes any residue that builds up in the tip’s bore, which causes inconsistent flow and gaps. For profiles, after each production run, wipe the tip’s exit face with a lint-free cloth dipped in isopropyl alcohol to remove any melted material buildup. I’ve seen customers skip this maintenance, and their new tips start developing gaps just 50 hours after installation, not 200 as expected.

Let’s get real with a customer story, because this isn’t just theory. Last quarter, a small sign shop reached out to me, saying they were getting 20-30% waste from gaps in their 3D printed letter signs. They were using generic brass tips, which wore out in about 15 hours of printing, and they were just replacing them with the same size. I recommended switching to hardened steel tips, sizing them 0.05mm larger than their filament, and calibrating their e-steps each time they swapped tips. After they made the change, their gap rate dropped to less than 2%, and their material waste went down by $1,200 a month. That’s the real impact of getting the tip right, not just swapping a part.

Now, if you’re still seeing gaps after installing a new tip, there are a few last checks to make. First, check your cooling: if your part isn’t cooling fast enough, the filament lines can’t bond, leading to gaps between layers. Make sure your part cooling fan is blowing directly on the print, and for thin layers, increase the fan speed to 100%. Second, check your hot end’s temperature: if it’s too low, the filament doesn’t melt properly, so it exits the tip in lumps, causing gaps. Use a thermocouple to verify the hot end’s temperature—sometimes the printer’s display is off by 10-20°F, which is enough to cause issues. Third, check your movement: if your printer’s belts are loose, or your extruder gears are worn, the filament isn’t feeding consistently, leading to gaps. Tighten belts and inspect gears if you suspect this.

At the end of the day, extrusion gaps don’t have to be a permanent headache. The biggest mistake I see is treating extrusion tips as a disposable, interchangeable part without considering their role in material flow. A new, correctly sized, properly installed tip isn’t just a replacement for a worn one—it’s an investment in less waste, faster prints, and higher quality parts. If you’re struggling with gaps that won’t go away no matter what you try, or you’re not sure which tip is right for your setup, don’t guess. Reach out to our team to talk through your specific needs—we’ll help you find the right tip, offer calibration tips, and make sure you’re set up to fix those gaps for good.

Extrusion Tips Reference

  1. Engineering Design Handbook: Extrusion Technology, U.S. Army Materiel Command, 1975
  2. Additive Manufacturing Materials and Processes, Gibson, D., Rosen, D., & Stucker, B., Springer, 2015
  3. Wear Behavior of Extrusion Tips for Fused Filament Fabrication, Journal of Manufacturing Processes, Vol. 35, 2018, pp. 452-459

Hejian Strains Of Hard Alloy Mould Co., Ltd.
As one of the most professional extrusion tips manufacturers and suppliers in China, we’re featured by quality products and good service. Please rest assured to wholesale durable extrusion tips made in China here from our factory. Also, custom service is available.
Address: Tangzhuang Industrial Park, Hejian City, Hebei Province
E-mail: limei@mouldzy.com
WebSite: https://www.mouldzy.com/