If you’ve ever stood next to a transformer in a power substation on a hot day, you’ve probably noticed that unassuming, small component bolted to its side: the transformer breather. At my company, we design, manufacture, and supply these breathers for everything from residential distribution transformers to large utility grid units, and I can’t tell you how often we get calls from maintenance teams, plant managers, and even other repair technicians asking the same question: “How do I clean this thing without breaking it, or worse, damaging the transformer it’s attached to?” Transformer Breather

First, let’s cut through the jargon and explain why this part matters so much. A transformer’s core and windings are submerged in mineral oil, which insulates against electricity and keeps all the internal components cool. When the transformer heats up during operation, the oil expands, and when it cools down at night or during off-peak use, it contracts. That means air has to move in and out of the transformer tank to equalize pressure. But that air is never perfectly dry—most of it has humidity, and even small amounts of moisture can wreak havoc on transformer oil. Too much moisture lowers the oil’s insulation resistance, causes corrosion on internal metal parts, and can even lead to breakdowns that take entire substations offline.
That’s exactly where the breather assembly comes in. The job of this part is simple: it filters the air moving into and out of the transformer, and removes almost all of the moisture before that air touches the oil. Most standard breathers use a desiccant material—usually silica gel or molecular sieve—that absorbs moisture. Once that desiccant is saturated, it stops working, and the breather becomes useless. A clogged breather, or a breather with old, saturated desiccant, leads to moisture buildup, reduced transformer lifespan, and costly unplanned outages. That’s why cleaning (and maintaining) the breather isn’t just a routine task—it’s critical for grid reliability.
Over the years, we’ve seen plenty of bad ways to clean a breather that end up causing more problems. Some people take a pressure washer to it, blasting away all the seals or cracking the plastic housing. Others open it up and dump fresh desiccant on top of old, caked-on dust and debris, which doesn’t address the actual buildup clogging the air pathways. Or worse, they skip cleaning entirely, assuming a quick wipe-down is enough. None of these work. A proper breather cleaning is a systematic process that gets rid of old desiccant, clears out the internal passages, replaces worn parts, and makes sure the unit is working as well as the day it left our factory.
Let’s walk through that step-by-step, the way we teach our customers when they call us for technical support (or when we train our own service teams before we ship units to job sites). Before you do anything, safety is non-negotiable. Transformers are connected to high-voltage lines, so you need to get a permit for electrical work, shut off power to the transformer, and lockout/tagout the system to make sure no one can accidentally re-energize it. You also need to wait long enough for the oil and the breather to cool down—no one wants to deal with hot mineral oil burns, or pressure releasing suddenly when you open a hot breather.
Once you’re in a safe working area, the first step is to disconnect the breather from the transformer tank. Most breathers are bolted on with two or three hex bolts, but take note: the fitting that connects the breather to the transformer is often a threaded brass or steel pipe, so don’t yank it. Gently loosen the bolts, and if it’s stuck, a little silicone lubricant on the threads (not inside the breather) will help. Once it’s off, set the unit on a clean, workbench surface—no dirt or dust here, because we don’t want any contaminants getting into the new clean parts.
Next, you’ll need to empty the old desiccant. This is where most people make the mistake: they just pour the old desiccant out and leave the fine dust that accumulates at the bottom of the chamber. That dust is part of the clogging problem—it can block airflow, making the desiccant work less effectively. So first, hold the breather over a trash bin and tap the sides gently to loosen the old desiccant. You can then use a small, soft-bristle brush (like a clean paintbrush with no paint residue) to wipe out the bottom of the desiccant chamber, getting all that fine dust out. If there’s any old desiccant caked to the walls of the chamber, you can use a plastic scraper (never metal—you don’t want to scratch or damage the interior, which can hold onto moisture) to gently work it loose.
Once the old desiccant and dust are out, it’s time to clean the external and internal surfaces of the breather. Skip the harsh chemicals—they can leave a residue that interferes with the desiccant’s ability to absorb moisture. Instead, use a lint-free cloth dampened with isopropyl alcohol, or even warm, soapy water with a mild dish soap. Wipe the exterior housing thoroughly, making sure to get any cobwebs, dust, or road grime that might have built up on it over time. For the internal passages, the small holes that air flows through between the desiccant chamber and the outside, use a can of compressed air (on a low setting, so you don’t damage the plastic or metal) to blow out any remaining debris. If there are clogged passages, you can gently use a soft pipe cleaner (again, not metal) to clear them, being careful not to bend or break the thin walls of the breather’s body.
Now, inspect all the parts of the breather while it’s empty—this is a step most people skip, but it’s just as important as cleaning. Check the gaskets, the rubber seals that fit between the top and bottom of the breather, and any O-rings that are around the desiccant cap or the connection to the transformer. If any of these seals are cracked, torn, or hardened, replace them immediately. A bad seal will let unfiltered, humid air into the transformer, no matter how clean the breather is. At our company, we keep replacement seals and gaskets in stock for all the breathers we supply, because this is such a common wear item. Also check the desiccant cap, the part that lets air flow in and out of the breather—make sure the vent holes aren’t clogged. If the cap is plastic and faded or brittle, replace it too, because brittle caps can crack, letting debris and moisture in.
Once everything is cleaned and inspected, it’s time to add new desiccant. The type of desiccant you use matters—silica gel is the most common, but molecular sieve is better for larger transformers that operate in very humid climates. The most important thing here is to make sure the desiccant is dry. Test it before you add it: if you have a sample, put it in a small container and leave it out for a few hours. If it doesn’t change color (most silica gel turns pink or blue when saturated), it’s ready. When adding it to the breather, don’t overfill the chamber—leave about a quarter of an inch of space at the top, so there’s room for air to flow around the desiccant. If you overfill it, the desiccant can block the vent holes, making the breather useless. Tap the sides of the breather gently after adding the desiccant to settle it, so there are no air pockets, then put the cap back on.
The final step is to reattach the breather to the transformer. Make sure the connection fitting is clean and dry before you thread it back on, and tighten the bolts evenly—don’t over-tighten them, that can crack the housing or strip the threads. Once it’s attached, turn the power back on to the transformer, and check the breather for any leaks. If you see oil or moisture coming from the seams, you may have a bad seal that you missed during inspection, so shut off power again and fix that.
Now, here’s what separates a good cleaning job from a great one, especially for our customers. After you clean and service a breather, you should log it in your maintenance records. When did you do it? What type of desiccant did you use? What was the color of the old desiccant (if it was already saturated, that’s a sign your transformer is operating in a very humid area, and you may need a breather with a larger desiccant chamber). We always recommend scheduling annual breather cleanings, or more often if you’re in a coastal area, a high-humidity region, or a place with lots of dust and air pollution that can clog the unit faster.
We’ve spent years refining our breather design, because we know that even the best unit only works if it’s properly maintained. We get emails every month from maintenance teams who tried a DIY cleaning on a cheap, imported breather and ended up damaging it, so they had to pay extra for a replacement. That’s why we supply not just breathers, but replacement parts, desiccant, and technical support for all our units.
If you’re responsible for maintaining transformers in a substation, a manufacturing plant, or a power utility, and you need reliable breather assemblies, replacement seals, desiccant, or expert guidance on cleaning and maintenance, we’re here to help. Our team has worked with hundreds of maintenance crews across the country, helping them avoid unplanned outages and extend the lifespan of their transformer fleets. Whether you need a single breather for a small distribution transformer, or a bulk order for a utility project, we can provide the high-quality parts and support you need.

Don’t wait until your breather fails and your transformer is at risk—regular cleaning and maintenance is the best way to keep your grid running smoothly. If you’re ready to place an order, or have questions about which breather is right for your application, reach out to our team to start a conversation about your needs.
Epoxy Bushing References
- IEEE Standard for Transformers – Design, Installation, and Maintenance Practices, IEEE Std C57.12.00-2015
- Transformer Breather Maintenance Guidelines, Electrical Maintenance and Reliability Association, 2021
- Silica Gel and Molecular Sieve Desiccant Performance for Power Transformer Applications, Journal of Electrical Insulation and Magnetics, Vol. 32, No. 4, 2020
Hebei Anmei Electrical Equipment Co., Ltd.
Hebei Anmei Electrical Equipment Co., Ltd. is one of the most professional transformer breather manufacturers and suppliers in China, specialized in providing high quality products and service. Please feel free to buy customized transformer breather made in China here from our factory. Contact us for quotation.
Address: Hejian Yingzhou Economic Development Zone, Cangzhou City, Hebei Province
E-mail: sales@anmeielec.com
WebSite: https://www.anmeibushing.com/