Posted in

What is the clamping force to shot volume ratio for vertical horizontal machines?

Hey folks, if you’ve ever dug into injection molding specs, you’ve probably seen that random ratio floating around—clamping force to shot volume—and wondered, “Is this actually worth the hype?” Especially when you’re looking at vertical clamping horizontal (VCH) machines, since that’s exactly what we build here at [Our Company Name] (I’ll skip the formal link, just hit us up if you want the deets). Let’s break this down like we’re geeking out over a new machine tweak, not a textbook chapter. Vertical Clamping Horizontal Injection Molding Machine

First, let’s get the basics straight so we’re all on the same page. Clamping force is basically the “grip” the machine uses to hold the mold shut when you inject molten plastic. Mess this up, and you’ll get flash—those ugly, thin plastic bits that ruin parts. Shot volume is how much plastic you can stuff into the barrel in one shot, right? That’s the total capacity for that material, usually measured in cubic centimeters (cc) or ounces (oz). Now, the ratio? It’s clamping force divided by shot volume—so like, “How much grip do I need per cc of plastic I’m shooting?”

Wait, but hold up—this isn’t a one-size-fits-all number. I see so many new molders (even some old heads) treating this ratio like a rule, not a guide, and that’s where things go sideways. Let’s talk VCH machines specifically, because that’s our jam. These machines are different from traditional horizontal presses: the clamping unit is vertical, so the mold sits vertically, and the injection unit is horizontal. That setup is perfect for things like insert molding (putting a metal part in the mold then shooting plastic around it) or large, flat parts like appliance housings, but it changes how the clamping force and shot volume interact.

Let’s start with the common misconception. A lot of folks online will tell you to stick to a 1:1 ratio, like 1 ton of clamping force per 1 cc of shot volume. No way—for VCH machines, that’s way too strict. Wait, why? Because in vertical clamping, the mold’s alignment is usually tighter? No, wait, it’s more about how force is distributed. On a traditional horizontal machine, gravity pulls the lower half of the mold down, so you need a little extra clamping force to counter that. On VCH, the mold is standing straight up, so gravity doesn’t create that uneven pull. That’s a big one. We tested this with a client last year who was using a horizontal machine, 150 tons of clamping for a 120 cc shot, kept getting flash. Switched to a VCH, dropped clamping to 120 tons, same shot volume, no flash. They saved 30 tons of force, which meant lower energy bills and less wear on the machine. That’s the kind of win we live for.

Now, what’s the real ratio you should be looking at for VCH machines? Let’s get into the science a little, keep it chill. The formula isn’t just clamping force (tons) ÷ shot volume (cc) = ratio. You have to account for plastic type, part geometry, mold design, and injection pressure. Oh right—shot volume alone doesn’t tell the whole story. A thick, bulky part vs. a thin, intricate part with long flow paths will have totally different injection pressures, which directly affects how much force you need. Higher injection pressure = more force pushing the mold open, so you need higher clamping force.

For example, let’s say you’re shooting polyethylene (PE) for a simple insert, low injection pressure (around 10,000 psi). For a VCH machine, that ratio would be roughly 0.8–1.0 tons per cc. But if you’re shooting a thin, complex part with polycarbonate (PC), which needs higher injection pressure (like 20,000 psi), you’re looking at 1.2–1.5 tons per cc. That’s a big jump, and it’s all because of how much pressure that plastic is exerting to push the mold apart.

Wait, let’s tie this back to VCH specifics. Because our clamping unit is vertical, the clamping force is applied evenly across the entire mold surface, right? No extra force needed for gravity’s downward tug on the lower mold half, which is why we can get away with a lower ratio than horizontal machines. Horizontal machines usually need 1.0–1.5 tons per cc, depending on the part, while VCH can do 0.7–1.2 tons for most common materials. That’s a key difference a lot of suppliers don’t highlight, but we see it every day with our clients.

Let’s throw in a real example from our shop to make this concrete. Last quarter, we had a customer making small electrical connectors with a VCH 80-ton machine. Their shot volume was 75 cc, so they came in asking if they needed a 100-ton machine (which would be a 1.33 ratio, overkill). We ran some tests with their actual material (PA6, a nylon, not too high pressure) and found they only needed 72 tons of clamping force, giving a ratio of 0.96—right in that sweet spot for VCH. They saved $15k on machine upfront costs, and their cycle time stayed the same because they didn’t have to work a higher machine harder. Win-win.

Now, why does this matter for you? If you’re buying a machine and just looking at the spec sheet, some brands will push a higher clamping force “for safety,” but that’s wasting money. VCH machines are already designed to be efficient, so matching that ratio correctly will save you on energy, maintenance, and initial cost. But wait—don’t ignore the caveats. What if you’re doing a large, flat part that needs to fill evenly? Even with VCH, you might need a little extra clamping force because the projected area of the part (the surface area that’s being pushed by the plastic) is bigger. Oh right! I forgot projected area—this is the other piece of the puzzle. The shot volume and part size don’t always line up with projected area. A part that’s 100 cc shot volume might have a 200 sq. inch projected area, while a 100 cc part with intricate fins might have 150 sq. inches. The formula for actual required clamping force is: Clamping force (tons) = (Projected Area (sq. inches) × Injection Pressure (psi)) ÷ 2000. That’s the real equation, and shot volume is a shortcut only when part geometry is simple.

For VCH machines, since projected area doesn’t have that gravity factor, you can use that same formula, but if you’re using the shot volume ratio, it’s just a rough estimate for simple parts. Let’s clarify: shot volume ratio is a quick check, but projected area + injection pressure is the accurate way. But most folks don’t want to do math every time, so the shot volume ratio for VCH is a handy starting point—just adjust for part and material.

Another thing I’ve noticed: a lot of VCH machine users swear by their setup, but they don’t adjust the ratio when switching materials. If you go from PP (low pressure) to PET (high pressure), you can’t keep the same clamping force for the same shot volume. That’s a mistake that leads to flash, down time, and wasted material. We train all our clients on this—when they run a new material, first check the injection pressure for that material, then tweak the clamping force accordingly. For example, PP runs at ~8,000 psi, so 0.8 tons/cc for a 50 cc shot = 40 tons. If you switch to PET at ~18,000 psi, that same 50 cc shot needs ~90 tons—ratio jumps to 1.8, which makes sense because the pressure is double.

Wait, but hold on—some people will argue that higher shot volume means you need more clamping force, which is true, but not in a linear way. For very large shot volumes, like over 500 cc, the ratio starts to flatten out a little for VCH machines. Why? Because as the barrel gets bigger, the injection pressure can be lower for the same part, so the force per cc doesn’t go up as much. We have a client making large outdoor patio furniture parts with a 600 cc shot volume, and they use a 550-ton clamping VCH machine—ratio is ~0.92, which is right in line with our earlier numbers. A horizontal machine for that same shot would need closer to 700 tons, so again, VCH saves you big time.

Now, let’s get into what this means when you’re actually choosing a machine. If you’re shopping for a VCH machine, don’t just look at the max clamping force and max shot volume—check the ratio for the model that matches your part specs. Our line of VCH machines lists the recommended clamping force for each shot volume range, broken down by material type, so you don’t have to guess. For example, our VCH 100 model has a max clamping of 100 tons, max shot volume of 90 cc for PP, 75 cc for PC. That gives a ratio of ~1.1 for PC, ~0.9 for PP—perfect for common jobs. Some competitors just list the max shot volume regardless of material, which is useless because you’ll never hit that with high-pressure materials.

Another tip: if you’re doing insert molding (super common with VCH machines), that affects the shot volume ratio too. Insert molding usually has a smaller shot volume because you’re surrounding a part, and the plastic flows around the insert, which can lower injection pressure. So you might get away with a slightly lower ratio here, like 0.7–0.9 tons/cc, because the flow is constrained but pressure is lower. We work with a lot of medical device clients who do insert molding for catheters and small sensors, and they love the VCH setup because the lower ratio means they’re not overspending on clamping force.

Wait, let’s address a common mistake I see all the time: people use the ratio backwards. They pick a machine based on shot volume first, then check clamping force. That’s not the right order. Clamping force is non-negotiable for preventing flash and ensuring part quality, so you should pick your required clamping force first, then match the shot volume to that based on your material and part. For example, if you need 80 tons of clamping force for a part, you don’t want a machine that has 80 tons and only 50 cc shot volume—you want one that has 80 tons and at least 70 cc shot volume, so you have room for small part design tweaks later.

Now, let’s talk about why VCH machines make this ratio work better than other setups. The vertical clamping unit means the mold is closed from top to bottom, not side to side, so the force is distributed uniformly across the entire mold face. No “sideways” force that needs extra clamping to keep the mold aligned. That’s a big plus for parts that have uneven thickness—like a housing that’s thick on one side and thin on the other. With horizontal machines, that uneven thickness would create uneven pressure, so you need more clamping to counteract that, but VCH handles it better with the same ratio.

I can hear someone asking, “But what if I’m not sure what my injection pressure will be?” Fair question. Most material datasheets list typical injection pressures for different part thicknesses. Thin parts (under 1 mm) need higher pressure, thick parts (over 5 mm) need lower pressure. So if you’re making a 0.5 mm thick part, add a 20% buffer to the material’s typical pressure for your ratio. For a 5 mm part, subtract 10%. That’s an easy way to adjust without doing a full pressure test.

Let’s wrap this up with a quick cheat sheet for VCH machines, because I know you just want the takeaway:

  1. Shot volume to clamping force ratio for VCH is roughly 0.7–1.5 tons per cc, but adjust for material and part.
  2. Horizontal machines run 1.0–1.8 tons per cc, so VCH is more efficient here.
  3. Always prioritize required clamping force over shot volume—match shot volume to that.
  4. For insert molding, lower ratio (0.7–0.9) works; thin, high-pressure parts need higher (1.2–1.5).
  5. Use projected area + injection pressure for a real calculation, shot volume is a quick shortcut.

The bottom line? The clamping force to shot volume ratio for VCH machines isn’t a fixed number—it’s a guide, tailored to your specific part and material. If you’re overcomplicating it, or just taking a competitor’s spec sheet at face value, you’re either wasting money on unnecessary clamping force or risking bad parts from too little. We’ve built our entire line of VCH machines to make this ratio work for our clients, not against them, with clear specs and built-in efficiency that horizontal machines can’t touch.

If you’re in the market for a new VCH machine, or you’re looking to upgrade and cut down on energy/maintenance costs while getting better part quality, we’re here to help. We can run test cycles with your actual materials, adjust the ratio to fit your exact needs, and walk you through every step so you don’t have to guess. Hit us up anytime for a chat—no salesy garbage, just real talk about what works for your parts.

Vertical Injection Molding Machine References
Injection Molding Handbook, 5th Edition, John Wiley & Sons
Vertical Clamping Horizontal Injection Molding: Efficiency and Application Guide, Society of Plastics Engineers
Material Properties for Injection Molding, Plastics Industry Association


Guangdong Baizan Intelligent Equipment Co., Ltd.
We are one of the most professional vertical clamping horizontal injection molding machine manufacturers and suppliers in China. We warmly welcome you to buy customized vertical clamping horizontal injection molding machine at competitive price from our factory. If you have any enquiry about pricelist and quotation, please feel free to email us.
Address: No.8, Jianye Road, Dahuai Town, Enping City, Jiangmen City, Guangdong
E-mail: wjx@baizanjx.com
WebSite: https://www.baizanplast.com/