Posted in

What is the hardness range for extruded EPDM?

If you’ve ever worked with rubber seals, gaskets, or weatherstripping, you’ve probably stumbled across EPDM—ethylene propylene diene monomer, that squishy, durable stuff that outlasts most other rubber materials when it comes to weather, UV rays, and temperature swings. As an extrusion supplier that’s been turning raw EPDM into custom profiles for everything from car door seals to warehouse dock bumpers for years, one of the first questions I get from new customers is: “What’s the hardness range for extruded EPDM?” It’s not a one-size-fits-all answer, and I see a lot of folks guessing wrong, which leads to parts that are too soft (they flatten out fast) or too hard (they don’t seal right, or crack during installation). Let’s break this down like we would over a coffee in my shop—not a textbook. EPDM Extrusion

First, let’s cut through the jargon. Hardness for rubber is measured on the Shore scale, specifically Shore A for most EPDM parts we extrude. If you’ve ever squeezed a new tire or a soft bouncy toy, that’s roughly where Shore A lives. Shore D is for way harder, rigid rubbers, and we almost never touch that for standard extruded EPDM. Why? EPDM is meant to flex, compress, and seal, not hold a sharp shape like a plastic pipe. So when we talk hardness here, it’s all Shore A.

The sweet spot for most general-purpose extruded EPDM is between 40 Shore A and 80 Shore A. That’s the range I recommend 9 times out of 10 for new customers who don’t have a super specific application in mind. But wait—there’s a reason that range is so wide. Let’s dig into what each end of that spectrum actually feels like and when you’d use it, because that’s where people mess up.

At the lower end, 40 to 50 Shore A. That’s EPDM so soft it almost feels like a thick foam eraser, not solid rubber. I remember a customer who came to us a couple years back asking for seals for a food processing conveyor. They thought softer would be gentler on their delicate packaged snacks, right? We warned them—45 Shore A EPDM seals way too fast, especially under constant compression from the conveyor’s weight. Six months later, they were back, complaining their seals were flattened like old gum. They switched to 60 Shore A, and those are still going strong three years later. So low Shore A EPDM is reserved for parts that never get squished hard, or just need a super flexible grip. Think: window channel inserts that hold small glass panes in place, or flexible gaskets for low-pressure door edges that don’t see heavy closing force. If you’re putting it on something that gets repeated compression—like a dock bumper, or a car trunk seal that slams shut every day—40-50 is a disaster waiting to happen.

Now the middle of the range, 55 to 70 Shore A. That’s the workhorse. This is where 80% of our orders land, and for good reason. It’s flexible enough to stretch around corners during installation, bounces back perfectly after being compressed, and holds its shape for decades. Let’s take two common examples: automotive weatherstripping and commercial refrigerator door gaskets. Car manufacturers almost always spec 60-65 Shore A for door seals. It’s soft enough to create a water-tight seal when you shut the door, but firm enough so it doesn’t sag if you park in the sun all summer, and doesn’t crack when it’s 20 degrees outside. For fridge gaskets, it’s similar—around 60 Shore A, because if it’s too soft, the door won’t stay closed, and if it’s too hard, there’s a gap that lets cold air escape and hikes up electricity bills. We also use this range for custom profiles like edge guards for furniture, or seals for farm equipment that gets exposed to rain and dust all year. It’s the balance everyone wants, and that’s why it’s the most requested.

Then the upper end of the general range, 75 to 80 Shore A. That’s EPDM that feels way firmer, like a new pencil eraser or the hard rubber on the bottom of a work boot. This is for applications that need to hold their shape under heavy force, or resist abrasion way more than the middle range. I’ve used 80 Shore A for dock bumpers before—they get hit by forklifts loaded with pallets, so if it was softer, it would flatten immediately. It’s also great for industrial gaskets that need to seal against high pressure, like on pipe joints that carry water or chemicals. Wait, but here’s the catch: 80 Shore A EPDM is much less flexible. You can’t bend it around a sharp corner without it cracking, and installation is trickier. We always warn customers ordering this that they need to make sure their parts are cut or formed to shape before curing, because trying to bend 80 Shore A post-extrusion is like bending a piece of hard plastic—it breaks. Also, don’t confuse 80 Shore A EPDM with something harder, like 90 Shore A; that’s almost rigid, and we only make custom profiles for super specific uses there, like some types of industrial hoses.

Now, why does the range vary so much anyway? It all comes down to the rubber compound. When we extrude EPDM, we mix the base EPDM polymer with fillers, oils, and curing agents to adjust hardness. Add more soft, oil-based fillers, and you get lower Shore A. Add more reinforcing fillers like carbon black, and you get higher Shore A. But it’s not just about hardness—those additives also change other properties, like UV resistance, temperature tolerance, and tear strength. A 40 Shore A EPDM might be soft, but it’ll tear if you snag it on a sharp edge. An 80 Shore A EPDM is tough, but it’s less flexible in cold weather. That’s why you can’t just pick a hardness number out of thin air; you have to match it to the job.

I’ve had customers come to us with a hardness spec they found online, and it’s wrong. Last month, a HVAC contractor asked for 50 Shore A EPDM for outdoor duct seals. I had to explain that 50 Shore A would become brittle in direct sun within a year—EPDM that soft loses its UV resistance faster. We adjusted them to 65 Shore A, which still seals great, and is built to handle outdoor conditions. That’s the thing about extrusion: we can tweak the hardness, but we have to balance it with the application.

Another common mistake: thinking higher hardness is better. Some folks see 80 Shore A and assume it’s a better product, but that’s not true. If you need a seal for a low-pressure door, 80 Shore A will make the door hard to close, and it won’t flex enough to create a tight seal. I learned this early in my career—we made a batch of 80 Shore A window seals for a customer’s camper, and he sent them back complaining they were impossible to fit. We remade them at 60 Shore A, and he’s been a repeat customer ever since. That’s why we always ask customers for details: what is this part sealing? How much force will it be under? What’s the environment like—hot? Cold? Outside? Inside?

Wait, what about special cases that fall outside the 40-80 Shore A range? Yeah, we do occasional orders outside that. For example, super soft EPDM for vibration dampers in industrial machinery—those need to absorb shock, so we’ll go as low as 35 Shore A. Or super hard EPDM for some electrical insulators, which can hit 90 Shore A. But those are niche, and most customers will never need them. 90% of what we extrude lands in that 40-80 Shore A sweet spot.

Let’s also talk about consistency, because that’s what matters when you’re ordering from an extrusion supplier. A lot of small shops might cut corners mixing their EPDM compounds, leading to hardness that’s all over the place. One batch is 60 Shore A, the next is 70, and your seals don’t work. At our shop, we test every batch of extruded EPDM with a Shore A durometer to make sure it’s within ±2 Shore A of the spec we agreed on. No surprises there.

So when you’re shopping for extruded EPDM, don’t just ask “what’s the hardness range?” Ask what hardness is right for your application. If you’re not sure, tell us what the part is for, and we’ll point you in the right direction. I’ve been doing this long enough that I can usually tell someone what hardness they need just by describing their project. Don’t guess—you’ll end up paying for parts that don’t work, and that’s a waste of time and money.

If you’re working on a project that needs custom extruded EPDM, whether it’s weatherstripping for a new build, seals for industrial equipment, or whatever else you’re working on, hit us up to chat through your needs. We don’t do one-size-fits-all here, and we’ll make sure you get the right hardness EPDM that works for your job.

EPDM Sheet References

  1. Rodgers, B. (2019). Rubber Compounding: Principles, Materials, and Techniques. Hanser Publications.
  2. ASTM D2240-15, Standard Test Method for Rubber Property—Durometer Hardness. ASTM International.
  3. EPDM Extrusion Best Practices. (2021). Industrial Rubber Extruders Association Technical Bulletin.

Jinjiang Yunli Technology Co., Ltd.
We’re known as one of the most reliable EPDM extrusion manufacturers and suppliers in China. With abundant experience, we warmly welcome you to buy customized EPDM extrusion at competitive price from our factory. If you have any enquiry about cooperation, please feel free to email us.
Address: Suqian Industrial Zone, Luoshan Street, Jinjiang City, Fujian Province, China
E-mail: sales@flexmer.com
WebSite: https://www.flexmers.com/